Measuring Feed Force in Machining Using a Strain Gage

Salman Al Farisi Siregar; Agus Triono; Mahros Darsin; Santoso Mulyadi

doi:10.22219/jemmme.v6i1.11928

Authors

Salman Al Farisi Siregar University of Jember
Agus Triono University of Jember
Mahros Darsin University of Jember
Santoso Mulyadi University of Jember

DOI:

https://doi.org/10.22219/jemmme.v6i1.11928

Keywords:

feeding force, strain gauge, ANOVA

Abstract

Measuring the forces that work during machining has been being concerned by researchers for years. There are three main forces that work in turning: thrust force, axial force, and radial force. Thus, feeding force measurement is needed in machine manufacturing. This research attempts to develop measurement method through feeding force, using strain gauge sensor. The aim of measurement of feeding force in this research is to find out the influence parameter of machine towards feeding force. The research used experimental method with design experiment Taguchi to know the influence of machine parameters to feeding force in turning process. The measurement tool is strain gauge sensor connected to cutting tool. The workspace is alluminium 6061 with 15 mm in diameter and 150 mm in length. The parameters for this research are speed rate (140 rpm, 215 rpm, and 330 rpm), feed rate (0,043 mm/r , 0,065 mm/r , and 0,081 mm/r), and depth of cut (0,2 mm, 0,4 mm, and 0,6 mm). The result showed that speed rate is the most significant parameter, with the contribution percentage is 92 %. Speed rate and feed rate parameter have insignificant influence. The contribution percentage of speed rate is 2% while the feed rate has % contribution percentage. The conclusion of the research is that the bigger number of speed rate, the bigger feeding force it will have.

Downloads

Download data is not yet available.

Author Biographies

Salman Al Farisi Siregar, University of Jember

Salman Al-Farisi Siregar

Jurusan Teknik Mesin Universitas Jember

Agus Triono, University of Jember

Dr. Agus Triono

Associate Professor in Mechanical Engineering, University of Jember

Mahros Darsin, University of Jember

Mahros Darsin, PhD

Santoso Mulyadi, University of Jember

Ir. Santoso Mulyadi, S.T., M.T.

Associate Professor in Mechanical Engineering, University of Jember

References

S. Kalpakjian and S. Schmid, Manufacturing Engineering and Technology, 4th ed. Pearson, 2001.

S. E. Oraby and D. R. Hayhurst, “Tool life determination based on the measurement of wear and tool force ratio variation,” Int. J. Mach. Tools Manuf., vol. 44, no. 12–13, pp. 1261–1269, 2004.

R. Dubovska, J. Majerik, and I. Baska, “Experimental Measurement of Cutting Forces in the Turning Technology,” Daaam Int. Sci. B. 2012, pp. 255–266, 2012.

S. V. A. Laakso, M. Agmell, and J. E. Ståhl, “The mystery of missing feed force — The effect of friction models, flank wear and ploughing on feed force in metal cutting simulations,” J. Manuf. Process., vol. 33, no. April, pp. 268–277, 2018.

S. K. Thangarasu, S. Shankar, A. Tony Thomas, and G. Sridhar, “Prediction of Cutting Force in Turning Process-an Experimental Approach,” IOP Conf. Ser. Mater. Sci. Eng., vol. 310, no. 1, 2018.

R. Manjunatha and C. K. Umesh, “Optimization of Tangential Force, Feed Force and Surface Roughness Using Taguchi Technique in Turning Operation,” Procedia Mater. Sci., vol. 5, pp. 1685–1691, 2014.

Y. Zhao et al., “Design and development of a cutting force sensor based on semi-conductive strain gauge,” Sensors Actuators, A Phys., vol. 237, pp. 119–127, 2016.

M. Luo, Z. Chong, and D. Liu, “Cutting Forces Measurement for Milling Process by Using Working Tables with Integrated PVDF,” Sensors, vol. 18, no. 4031, pp. 1–13, 2018.

X. Li, P. K. Venuvinod, and M. K. Chen, “Feed Cutting Force Estimation from the Current Measurement with Hybrid Learning,” Int J Adv Manuf Technol, vol. 16, pp. 859–862, 2000.

M. Wan, W. Yin, and W. Zhang, “Study on the correction of cutting force measurement with table dynamometer,” Procedia CIRP, vol. 56, pp. 119–123, 2016.

M. Darsin, T. Pasang, and Z. Chen, “Forces Perspective of Drillability of Titanium Alloy 6Al-2Sn-4Zr-6Mo,” J. Energy, Mech. Mater. Manuf. Eng., vol. 3, no. 1, p. 23, Jun. 2018.

N. Khanna and J. P. Davim, “Design-of-experiments application in machining titanium alloys for aerospace structural components,” vol. 61, pp. 280–290, 2015.

V. Sivaraman, S. Sankaran, and L. Vijayaraghavan, “The Effect of Cutting Parameters on Cutting Force During Turning Multiphase Microalloyed Steel,” vol. 4, pp. 157–160, 2012.

Q. Liu and T. Homma, “A New Importance Measure for Sensitivity Analysis A New Importance Measure for Sensitivity Analysis,” J. Nucl. Sci. Technol. ISSN, vol. 3131, no. 2010, pp. 53–61, 2012.