The Effect of Mesh Size on Mechanical and Thermal Properties of Bamboo Composites

Authors

  • Ziani Adriant Universitas Pancasila, Jakarta
  • Yulianto Yulianto Universitas Pancasila, Jakarta
  • Ralf Förster Beuth University, Luxemburger
  • Dede Lia Zariatin Universitas Pancasila, Jakarta

DOI:

https://doi.org/10.22219/jemmme.v4i2.9698

Keywords:

Coolbox composite of black bamboo fiber, tensile test, compressive test, impact test, thermal conductivity test.

Abstract

The application of styrofoam in food storage causes environmental contamination. The foam material is containing styrene that creates a dangerous risk in food storage. The objective of the research is to investigate the feasibility of using black bamboo-composite as a coolbox material. In this research, there was three sizes of meshing was manufactured which are mesh 40, 30 and 20. The materials were composed of 30% black bamboo fiber and 70% SHCP 2668 resin. Six side sheet plates of composite did assemble using adhesive bonding method into a box shape. Several tests were performed which are tensile test, compressive test, impact test, and thermal conductivity test according to ASTM D638, ASTM D6411, ASTM D6110, and ASTM C1004 respectively.Mesh size 40 has the highest tensile test, compressive test, and impact test was the value of 17,4 MPa, 54,13 MPa, 0,085 Joule/mm2 respectively. Mesh size 20 has the best thermal conductivity was the value of 7.36 W/m.oC. Coolbox testing on mesh 20, 30, 40 compared with the same dimensions was given box styrofoam with a temperature of -2 oC. The results of the coolbox composite test against mesh size 20 have slower ice cube melting compared to mesh 30 and 40.

Downloads

Download data is not yet available.

Author Biographies

Ziani Adriant, Universitas Pancasila, Jakarta

Department of Mechanical Engineering

Yulianto Yulianto, Universitas Pancasila, Jakarta

Department of Mechanical Engineering

Ralf Förster, Beuth University, Luxemburger

Department of Mechanical Engineering

Dede Lia Zariatin, Universitas Pancasila, Jakarta

Department of Mechanical Engineering

References

F. Kalanzi, C. Mwanja, H. Agaba, and R. T. Guuroh, “Potential of Bamboo as a Source of Household Income in South Western Uganda,” vol. 16, no. 1, pp. 33–45, 2017.

D. A. Porwanto and L. Johar, “Characterization of Bamboo Fiber and Fiber Glass Composite as an Alternative Raw Material for Industry,” ITS Libr., 2011.

B. Hirmawan, J. M. Lizda, and I. Doty, “Sifat Mekanik Komposit Serat Bambu Akibat Pengaruh Musim Hujan Dengan / Tanpa Pelapisan,” Inst. Sepuluh Novemb., pp. 1–8, 2013.

S. A. Irianto, “PENGARUH FRAKSI VOLUME BILAH BAMBU TERHADAP KEKUATAN IMPACT KOMPOSIT BILAH BAMBU / POLYESTER,” 2016. .

Sulistijono.Prof.Dr.Ir, Mekanika Material Komposit, Pertama. Surabaya: ITS Press, 2012.

E. Sutardi, Sri Rulliaty. Nadjib, Nurwati. Muslich, Muhammad. Jasni. Sulastiningsih I M. Komaryati, Sri. Suprapti, Sihati. Abdurrahman. Basri, Informasi Sifat Dasar dan Kemungkinan Penggunaan 10 Bambu. Bogor: PUSAT PENELITIAN DAN PENGEMBANGAN HASIL HUTAN BADAN PENELITIAN, PENGEMBANGAN DAN INOVASI KEMENTERIAN LINGKUNGAN HIDUP DAN KEHUTANAN, 2015.

S. Highpolymer, “SHCP 2668 CM-M POLYESTER RESIN FOR SHEET LAMINATING.”

P. Frederik, “Karakterisasi Sifat Mekanik Komposit Penguatan Bambu Hasil Fabrikasi Dengan Metode Hand Lay Up,” Jakarta, 2007.

Purnomo, Material Teknik, Pertama. Malang: CV. Seribu Bintang, 2017.

ASTM, “Standard Test Method For Tensile Properties Of Plastics 1,” ASTM D 638, Pp. 4–7, 2015.

S. Hadi, Teknologi Bahan. Yogyakarta: ANDI Yogyakarta, 2016.

ASTM, “Standard Test Method For Compressive Properties Of Polymer Matrix Composite Materials Using A Combined Loading Compression ( CLC ),” ASTM D 6641, No. Clc, Pp. 1–11, 2014.

I. I. Widya Emilia Primaningtyas, Suheni, “Pengaruh Orientasi Serat Kaca Terhadap Kekuatan Impact Pada Bodi Mobil Prototipe Mobil Listrik,” J. IPTEK, vol. 21, pp. 35–42, 2017.

ASTM, “Standard Test Method For Determining The Charpy Impact Resistance Of Notched,” ASTM D 6110, Vol. 1, Pp. 5–8, 2004.

ASTM, “Standard Practice for Using a Guarded-Hot-Plate Apparatus or Thin-Heater Apparatus in the Single-Sided Mode 1,”ASTM C1044, August, 1998, pp. 1–8.

S. and S. R. S. Kalpakjian, MANUFACTURING ENGINEERING Illinois Institute of Technology, Six Edition. Pearson, 2009.

Downloads

Published

2019-11-30

How to Cite

Adriant, Z., Yulianto, Y., Förster, R., & Zariatin, D. L. (2019). The Effect of Mesh Size on Mechanical and Thermal Properties of Bamboo Composites. Journal of Energy, Mechanical, Material, and Manufacturing Engineering, 4(2), 63–72. https://doi.org/10.22219/jemmme.v4i2.9698

Issue

Vol. 4 No. 2 (2019)

Section

Articles

License

Authors who publish with this journal agree to the following terms:

  1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution-NonCommercial 4.0 International License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
  2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
  3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).

Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.