STRUCTURAL BEHAVIOR OF PILE CAP 3 PILE WITH EKSENTRIC LOAD DESIGNED USING STRUT AND TIE MODEL WITH NUMERICAL METHOD
DOI:
https://doi.org/10.22219/jmts.v17i1.7483Keywords:
strut and tie model, pile cap, eccentric load, AbaqusAbstract
Pile cap is a structure to distribute load from the upper structure to the sub structure. Often the planning of the pile cap is approached as a two way slab or beam with pile as restrain, by consider the bending and shear separately. As is the case with conventional methods that consider 1-way shear, 2-way shear, and bending separately. The strut and tie model can be used as an alternative method in designing a pile cap, by approaching the stress trajectory with the truss model. In this study, a pile cap will be designed using the conventional method and the strut and tie model, the pile cap with 3 pile cap and an eccentric load. Then the results are tested numerically using Abaqus to determine the difference in behavior. The main reinforcement results from the strut and tie model method are more evenly stressed than the conventional method, also the vertical load needed to achieve the main reinforcement yield stress strut and tie model (1100 kN) is greater than the conventional method (900 kN).
Downloads
References
Badan Standarisasi Nasional. (2013). Persyataratn Beton Struktural untuk Bangunan Gedung. Jakarta: BSN.
Buswell, W., & Dao, V. (2013). Pile Cap Design Using Strut-and-Tie Modelling. The 26th Biennial Conference of the Concrete Institute of Australia. Gold Coast: Researchgate.
Fellenius, B. (2006). Basics of Foundation Design. Calgary: www.Fellenius.net.
Hardiyatmo, H. C. 2010. Analisis & Perancangan Fondasi Bagian II. Yogyakarta: Gadjah Mada University Press.
Hardjasaputra, H. (2016). Perancangan Beton Struktural Berdasarkan Model Strat dan Pengikat (Strut-and-Tie Model) SNI 2847-2013. Jakarta: Jurusan Teknik Sipil Universitas Pelita Harapan.
Hardjasaputra, H., & Tumilar, S. (2002). Model Penunjang dan Pengikat (Strut and Tie Model) pada Perancangan Struktur Beton. Jakarta: Universitas Pelita Harapan Press.
Nori, & Tharval, M. (2007). Design of pile caps – Strut and tie model method. The Indian Concrete Journal, 13-19.
Suhendro, B. (2000). Teori Model Struktur dan Teknik Eksperimental. Yogyakarta: Beta Offset.
Teng, W. (1992). Foundation Design. Englewood Cliffs, New Jersey: Prentice-Hall.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2019 Panji Ginaya Taufik, Djoko Sulistyo, Akhmad Aminullah
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution-ShareAlike 4.0 International License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).
MEDIA TEKNIK SIPIL Journal
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.